The ESP32-S3-DevKitC-1 is an entry-level development board equipped with ESP32-S3-WROOM-1, a general-purpose Wi-Fi + Bluetooth LE MCU module that integrates complete Wi-Fi and Bluetooth LE functions. This version is equipped with the ESP32-S3-WROOM-1 (PCB antenna) with 8MB Flash and 8MB PSRAM.
Please note: The S3 is similar to the ESP32-S2 - but adds a dual core and Bluetooth LE (not classic!) However, there is minimal support for this dev board. For example, as of the time of this writing, there is no Arduino or CircuitPython support - only ESP IDF! Please purchase if you’re doing development with the S3, and OK with stuff not working 100% out of the box.
Most of the I/O pins on the module are broken out to the pin headers on both sides of this board for easy interfacing. Developers can either connect peripherals with jumper wires or mount ESP32-S3-DevKitC-1 on a breadboard. We particularly like that there’s a debug UART/USB port and a separate native USB port, so you can upload/debug/USB all at once.
At the core of the module is an ESP32-S3FN8, an Xtensa® 32-bit LX7 CPU that operates at up to 240 MHz. You can power off the CPU and make use of the low-power co-processor to constantly monitor the peripherals for changes or crossing of thresholds.
ESP32-S3FN8 integrates a rich set of peripherals including SPI, LCD, Camera interface, UART, I2C, I2S, remote control, pulse counter, LED PWM, USB Serial/Jtag, MCPWM, SDIO host, GDMA, TWAI® controller (compatible with ISO 11898-1, i.e. CAN Specification 2.0), ADC, touch sensor, temperature sensor, timers, and watchdogs, as well as up to 45 GPIOs. It also includes a full-speed USB 1.1 On-The-Go (OTG) interface to enable USB communication
There are three mutually exclusive ways to provide power to the board:
- USB-to-UART Port and ESP32-S3 USB Port (either one or both), default power supply (recommended)
- 5V and G (GND) pins
- 3v3 and G (GND) pins
- ESP32-S3-WROOM-1: ESP32-S3-WROOM-1 is a powerful, generic Wi-Fi + Bluetooth LE MCU module that has a rich set of peripherals. It provides acceleration for neural network computing and signal processing workloads. ESP32-S3-WROOM-1 comes with a PCB antenna.
- 5V to 3.3V LDO: Power regulator that converts a 5V supply into a 3.3V output.
- Pin Headers: All available GPIO pins (except for the SPI bus for flash) are broken out to the pin headers on the board for easy interfacing and programming. For details, please see Header Block.
- USB-to-UART Port: A Micro-USB port used for power supply to the board, for flashing applications to the chip, as well as for communication with the chip via the on-board USB-to-UART bridge.
- Native ESP32-S3 USB Port: ESP32-S3 full-speed USB OTG interface, compliant with the USB 1.1 specification. The interface is used for power supply to the board, for flashing applications to the chip, for communication with the chip using USB 1.1 protocols, as well as for JTAG debugging.
- Boot Button: Download button. Holding down Boot and then pressing Reset initiates Firmware Download mode for downloading firmware through the serial port.
- Reset Button
- USB-to-UART Bridge: Single USB-to-UART bridge chip provides transfer rates up to 3 Mbps.
- RGB LED: Addressable RGB LED, driven by GPIO48.
- 3.3V Power On LED: Turns on when the USB power is connected to the board.
Have some info to add for this board? Edit the source for this page here.
This is the latest stable release of CircuitPython that will work with the ESP32-S3-DevKitC-1-N8R8.
Start here if you are new to CircuitPython.
Built-in modules available: _bleio, adafruit_bus_device, adafruit_pixelbuf, aesio, alarm, analogio, atexit, audiobusio, audiocore, audiomixer, binascii, bitbangio, bitmaptools, board, busio, canio, countio, digitalio, displayio, dualbank, errno, fontio, framebufferio, frequencyio, getpass, gifio, i2cperipheral, ipaddress, json, keypad, math, mdns, microcontroller, msgpack, neopixel_write, nvm, onewireio, os, ps2io, pulseio, pwmio, rainbowio, random, re, rgbmatrix, rotaryio, rtc, sdcardio, sharpdisplay, socketpool, ssl, storage, struct, supervisor, synthio, terminalio, time, touchio, traceback, ulab, usb_cdc, usb_hid, usb_midi, vectorio, watchdog, wifi, zlib
This is the latest unstable release of CircuitPython that will work with the ESP32-S3-DevKitC-1-N8R8.
Unstable builds have the latest features but are more likely to have critical bugs.
Built-in modules available: _asyncio, _bleio, _pixelmap, adafruit_bus_device, adafruit_pixelbuf, aesio, alarm, analogio, array, atexit, audiobusio, audiocore, audiomixer, binascii, bitbangio, bitmaptools, board, builtins, busio, canio, collections, countio, digitalio, displayio, dualbank, errno, fontio, framebufferio, frequencyio, getpass, gifio, hashlib, i2ctarget, ipaddress, json, keypad, math, mdns, memorymap, microcontroller, msgpack, neopixel_write, nvm, onewireio, os, ps2io, pulseio, pwmio, qrio, rainbowio, random, re, rgbmatrix, rotaryio, rtc, sdcardio, select, sharpdisplay, socketpool, ssl, storage, struct, supervisor, synthio, sys, terminalio, time, touchio, traceback, ulab, usb_cdc, usb_hid, usb_midi, vectorio, watchdog, wifi, zlib
Every time we commit new code to CircuitPython we automatically build binaries for each board and language. The binaries are stored on Amazon S3, organized by board, and then by language. Try them if you want the absolute latest and are feeling daring or want to see if a problem has been fixed.
All previous releases are listed on GitHub, with release notes, and are available for download from Amazon S3. They are handy for testing, but otherwise we recommend using the latest stable release. Some older GitHub release pages include the same binaries for downloading. But we have discontinued including binaries as assets on newer release pages because of the large number of files for each release.
Install, Repair, or Update UF2 Bootloader
Latest version: 0.11.0
The UF2 bootloader allows you to load CircuitPython, MakeCode, and Arduino programs. The bootloader is not CircuitPython. If a UF2 bootloader is installed, you can check its version by looking in the INFO_UF2.TXT file when the BOOT drive is visible (FTHRS2BOOT, MAGTAGBOOT, HOUSEBOOT, etc.)
It is not necessary to reinstall a UF2 bootloader you unless a BOOT drive is not visible when in UF2 bootloader mode, or you know of a problem with your current UF2 bootloader.
If a UF2 bootloader has never been installed on the board, or the UF2 bootloader was removed by erasing or overwriting the flash, the UF2 bootloader must be installed in order to flash .uf2 files onto the board. .bin files can be uploaded without a UF2 bootloader, using the ESP Web Flasher or esptool.py.
Note: update.uf2 files are not currently working on ESP32-S2 or ESP32-S3 boards.
Important: this will erase previously flashed firmware and sketches from the board, but needs to be perfomed only once.
The instructions here are general. We recommend you consult the manufacturer's board documentation for detailed instructions, which may be different.
- Unzip to find the file combined.bin.
- Place board in bootloader mode:
- Plug board into a USB port on your computer using a data/sync cable. Make sure it is the only board plugged in, and that a charge-only cable is not being used.
- Press and hold down the BOOT or 0 button.
- Press and release the RESET or RST button.
- Release the BOOT button.
- Upload combined.bin (Google Chrome 89 or newer):
- Open ESP Web Flasher in a new window/tab.
- Select 460800 Baud from the pull-down menu (top-right).
- Click Connect (top-right).
- Select the COM or Serial port from the pop-up window.
- After successful connection, click Erase.
- After successful erase, click any Choose a file..., then locate and select the combined.bin file unzipped earlier.
- After successfully choosing combined.bin, click Program.
- After the TinyUF2 firmware update is complete, press the RESET button on the board. A new drive BOOT should be visible in your file browser.
After installing the UF2 bootloader, enter the bootloader by double-clicking the reset button. On boards with an RGB status LED, tap reset once, wait for the LED to turn purple, and tap again before the purple goes away. On other boards, consult the board documentation.
After you update, check INFO_UF2.TXT to verify that the bootloader version has been updated. Then you will need to load or reload CircuitPython using the .uf2 file.