Seeed Studio XIAO SAMD21
by Seeed Studio
Seeed Studio XIAO SAMD21 is a minimal, low-cost board that uses the Atmel ATSAMD21G18, a powerful 32-bit ARM Cortex®-M0+ processor running at 48MHz with 256 KB Flash and 32 KB SRAM. The board is 20 mm x 17.5 mm in size which is perfect for wearable devices and small projects. It has multiple interfaces including DAC output, SWD Bonding pad interface, I2C, UART and SPI interfaces. It’s compatible with both Arduino IDE and CircuitPython and uses a USB-C connector.
Technical details
- CPU: ARM Cortex-M0+ CPU (SAMD21G18) running at up to 48 MHz
- Flash Memory: 256 KB
- SRAM: 32 KB
- Digital I/O pins: 11
- Analog I/O pins: 11
- I2C interfaces: 1
- SPI interfaces: 1
- UART interfaces: 1
- USB-C connector for transferring code and power
- Power requirements: 3.3 V/5 V DC
- Dimensions: 20 mm x 17.5 mm x 3.5 mm
Note: This microcontroller runs at 3.3 V logic. Using a 5 V device may damage the chip or device.
For power supply pins: The built-in DC-DC converter circuit is able to change 5 V voltage into 3.3 V, which allows you to power the device with a 5 V supply via the VIN pin or 5V pin.
Tutorial
Purchase
Contribute
Have some info to add for this board? Edit the source for this page here.
CircuitPython 9.2.1
This is the latest stable release of CircuitPython that will work with the Seeed Studio XIAO SAMD21.
Use this release if you are new to CircuitPython.
Built-in modules available: analogio, array, board, builtins, busio, busio.SPI, busio.UART, collections, digitalio, math, microcontroller, neopixel_write, nvm, os, pwmio, rainbowio, random, rotaryio, rtc, storage, struct, supervisor, sys, time, touchio, usb_cdc, usb_hid, usb_midi
Features: USB-C, Breadboard-Friendly, Xiao / QTPy Form Factor, Castellated Pads
Absolute Newest
Every time we commit new code to CircuitPython we automatically build binaries for each board and language. The binaries are stored on Amazon S3, organized by board, and then by language. These releases are even newer than the development release listed above. Try them if you want the absolute latest and are feeling daring or want to see if a problem has been fixed.
Previous Versions of CircuitPython
All previous releases of CircuitPython are available for download from Amazon S3 through the button below. For very old releases, look in the OLD/ folder for each board. Release notes for each release are available at GitHub button below.
Older releases are useful for testing if you something appears to be broken in a newer release but used to work, or if you have older code that depends on features only available in an older release. Otherwise we recommend using the latest stable release.
Update UF2 Bootloader
Latest version: v3.15.0
The bootloader allows you to load CircuitPython, MakeCode, and Arduino programs. The bootloader is not CircuitPython. You can check the current version of your bootloader by looking in the INFO_UF2.TXT file when the BOOT drive is visible (FEATHERBOOT, CPLAYBOOT, etc.).
It is not necessary to update your bootloader if it is working fine. Read the release notes on GitHub to see what has been changed. In general, we recommend you not update the bootloader unless you know there is a problem with it or a support person has asked you to try updating it.
To update, first save the contents of CIRCUITPY, just in case. Then double-click the reset button to show the BOOT drive. Drag the update-bootloader .uf2 file to the BOOT drive. Wait a few tens of seconds for the bootloader to update; the BOOT drive will reappear. After you update, check INFO_UF2.TXT to verify that the bootloader version has been updated. Then you will need to reload CircuitPython.