Unexpected Maker NanoS3

by Unexpected Maker

Image of Board

Introducing the NanoS3 - The world’s smallest, fully-featured ESP32-S3 board in module form!

Features & Specifications

  • Dual 32bit Xtensa LX7 cores @ up to 240Mhz
  • RISC-V Ultra Low Power Co-processor
  • 2.4GHz Wifi - 802.11b/g/n
  • BLE 5.0 + Mesh
  • 8MB QSPI Flash
  • 8MB of extra QSPI PSRAM
  • 700mA 3.3V LDO Regulator
  • Low power RGB LED
  • ULTRA LOW Deep Sleep Current
  • 5V back-feed protection
  • Native USB + USB Serial JTAG
  • LiPo Battery Charging
  • 27 GPIO
  • Only 28 x 11mm in size
  • Drop in compatible with TinyPICO Nano
  • Available with 3D High Gain Antenna or u.FL for external Antenna

You can find out more about the NanoS3 at nanos3.io

Purchase

You can purchase your very own NanoS3 from:

Contribute

Have some info to add for this board? Edit the source for this page here.

CircuitPython 9.2.1

This is the latest stable release of CircuitPython that will work with the Unexpected Maker NanoS3.

Use this release if you are new to CircuitPython.

Release Notes for 9.2.1

DOWNLOAD .UF2 NOW DOWNLOAD .BIN NOW

Built-in modules available: _asyncio, _bleio, _eve, _pixelmap, adafruit_bus_device, adafruit_pixelbuf, aesio, alarm, analogbufio, analogio, array, atexit, audiobusio, audiocore, audiomixer, audiomp3, binascii, bitbangio, bitmapfilter, bitmaptools, board, builtins, builtins.pow3, busdisplay, busio, busio.SPI, busio.UART, canio, codeop, collections, countio, digitalio, displayio, dualbank, epaperdisplay, errno, espcamera, espidf, espnow, espulp, fontio, fourwire, framebufferio, frequencyio, getpass, gifio, hashlib, i2cdisplaybus, io, ipaddress, jpegio, json, keypad, keypad.KeyMatrix, keypad.Keys, keypad.ShiftRegisterKeys, keypad_demux, keypad_demux.DemuxKeyMatrix, locale, math, max3421e, mdns, memorymap, microcontroller, msgpack, neopixel_write, nvm, onewireio, os, os.getenv, paralleldisplaybus, ps2io, pulseio, pwmio, qrio, rainbowio, random, re, rgbmatrix, rotaryio, rtc, sdcardio, sdioio, select, sharpdisplay, socketpool, socketpool.socketpool.AF_INET6, ssl, storage, struct, supervisor, synthio, sys, terminalio, time, touchio, traceback, ulab, usb, usb_cdc, usb_hid, usb_midi, vectorio, warnings, watchdog, wifi, zlib

Included frozen(?) modules: neopixel

Features: Battery Charging, Bluetooth/BTLE, Wi-Fi, Castellated Pads

Absolute Newest

Every time we commit new code to CircuitPython we automatically build binaries for each board and language. The binaries are stored on Amazon S3, organized by board, and then by language. These releases are even newer than the development release listed above. Try them if you want the absolute latest and are feeling daring or want to see if a problem has been fixed.

Previous Versions of CircuitPython

All previous releases of CircuitPython are available for download from Amazon S3 through the button below. For very old releases, look in the OLD/ folder for each board. Release notes for each release are available at GitHub button below.

Older releases are useful for testing if you something appears to be broken in a newer release but used to work, or if you have older code that depends on features only available in an older release. Otherwise we recommend using the latest stable release.

BROWSE S3 BROWSE GITHUB

Install, Repair, or Update UF2 Bootloader

Latest version: 0.20.1

The UF2 bootloader allows you to load CircuitPython, MakeCode, and Arduino programs. The bootloader is not CircuitPython. If a UF2 bootloader is installed, you can check its version by looking in the INFO_UF2.TXT file when the BOOT drive is visible (FTHRS2BOOT, MAGTAGBOOT, HOUSEBOOT, etc.)

It is not necessary to reinstall a UF2 bootloader you unless a BOOT drive is not visible when in UF2 bootloader mode, or you know of a problem with your current UF2 bootloader.

If a UF2 bootloader has never been installed on the board, or the UF2 bootloader was removed by erasing or overwriting the flash, the UF2 bootloader must be installed in order to flash .uf2 files onto the board. .bin files can be uploaded without a UF2 bootloader, using the ESP Web Flasher or esptool.py.

Note: update.uf2 files are not currently working on ESP32-S2 or ESP32-S3 boards.

Important: this will erase previously flashed firmware and sketches from the board, but needs to be perfomed only once.

The instructions here are general. We recommend you consult the manufacturer's board documentation for detailed instructions, which may be different.

  • Unzip to find the file combined.bin.
  • Place board in bootloader mode:
    • Plug board into a USB port on your computer using a data/sync cable. Make sure it is the only board plugged in, and that a charge-only cable is not being used.
    • Press and hold down the BOOT or 0 button.
    • Press and release the RESET or RST button.
    • Release the BOOT button.
  • Upload combined.bin (Google Chrome 89 or newer):
    • Open ESP Web Flasher in a new window/tab.
    • Select 460800 Baud from the pull-down menu (top-right).
    • Click Connect (top-right).
    • Select the COM or Serial port from the pop-up window.
    • After successful connection, click Erase.
    • After successful erase, click any Choose a file..., then locate and select the combined.bin file unzipped earlier.
    • After successfully choosing combined.bin, click Program.
    • After the TinyUF2 firmware update is complete, press the RESET button on the board. A new drive BOOT should be visible in your file browser.

After installing the UF2 bootloader, enter the bootloader by double-clicking the reset button. On boards with an RGB status LED, tap reset once, wait for the LED to turn purple, and tap again before the purple goes away. On other boards, consult the board documentation.

After you update, check INFO_UF2.TXT to verify that the bootloader version has been updated. Then you will need to load or reload CircuitPython using the .uf2 file.